





   TM    WELCOME TO C&D PROGRAMMING CORP.'S:
                                
                                                  CacheAll(tm)
                 
                          The Cache of the 90's!(tm)
              
      \                      Order Line: (800) 847-5676
      \ \           Orders Outside U.S.A.: (801) 582-0503
      \ \ \                                BBS: (516) 434-8712
       \ \ \          
       \ \ \       Corporate Headquarters:
       \ \ \          PO Box 1305
        \ \ \         Brentwood, NY 11717 USA
          \ \ \ 
                         \ \ \ 
                         \ \ \
                         \ \    Sales Office:
                         \        PO Box 581012
                                Salt Lake City, UT 84158
                                 USA
              FAX (801) 581-0883

    P  R  O  G  R  A  M  M  I  N  G







                             Copyright (c), 1992-93
                              C&D Programming Corp.
                              All Rights Reserved.

        This evaluation version of CacheAll(tm), The Cache of the 90's!(tm),
   may be freely copied and distributed for the purpose of evaluating
   CacheAll(tm) under the conditions that CacheAll(tm), CUtil(tm) and the
   accompanying software,

             (1)  will not be sold,
             (2)  will not be reverse engineered,
             (3)  will not be modified,
             (4)  will not be incorporated, in whole or in part, into any
                  other computer program,

   CacheAll, CUtil, AppTrack and "The Cache of the 90's!" are trademarks of
   C&D Programming Corp.

   All product names and services identified throughout this manual are
   trademarks or registered trademarks of their respective companies.


   CacheAll Evaluation Manual                                           Page i
   --------------------------------------------------------------------------
   -

                                Table of Contents

   About CacheAll(tm), The Cache of the 90's!(tm), . . . . . . . . . . .     1
   About The Evaluation Version of CacheAll  . . . . . . . . . . . . . .     3
   How to Order CacheAll . . . . . . . . . . . . . . . . . . . . . . . .     3
   What do you get when you purchase CacheAll? . . . . . . . . . . . . .     4
   Technical Support -- How to reach us  . . . . . . . . . . . . . . . .     5

   Welcome to CacheAll . . . . . . . . . . . . . . . . . . . . . . . . .     6
   Before Installing CacheAll  . . . . . . . . . . . . . . . . . . . . .     7
   System Requirements . . . . . . . . . . . . . . . . . . . . . . . . .     7
   Application Compatibility for CacheAll  . . . . . . . . . . . . . . .     8

   Software Installation . . . . . . . . . . . . . . . . . . . . . . . .    10
   Preparing Your System For CacheAll  . . . . . . . . . . . . . . . . .    10
   About INSTALL . . . . . . . . . . . . . . . . . . . . . . . . . . . .    10
   Starting INSTALL  . . . . . . . . . . . . . . . . . . . . . . . . . .    11

   BEGINNERS: CacheAll is SMART! . . . . . . . . . . . . . . . . . . . .    14
   Running CacheAll  . . . . . . . . . . . . . . . . . . . . . . . . . .    15
   Unloading CacheAll  . . . . . . . . . . . . . . . . . . . . . . . . .    15
   CacheAll Options  . . . . . . . . . . . . . . . . . . . . . . . . . .    16
   CacheAll Option File  . . . . . . . . . . . . . . . . . . . . . . . .    23
   CacheAll Error Messages . . . . . . . . . . . . . . . . . . . . . . .    24

   CUtil(TM) Introduction  . . . . . . . . . . . . . . . . . . . . . . .    28
   CUtil for DOS . . . . . . . . . . . . . . . . . . . . . . . . . . . .    29
   CUtil Options . . . . . . . . . . . . . . . . . . . . . . . . . . . .    30
   CUtil for Windows . . . . . . . . . . . . . . . . . . . . . . . . . .    33

   Technical Specifications  . . . . . . . . . . . . . . . . . . . . . .    37
   Benchmarks  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    37
   Caching only specific drive directories . . . . . . . . . . . . . . .    39
   Using CacheAll to Speed up Networks . . . . . . . . . . . . . . . . .    40

   Swap Files for CacheAll . . . . . . . . . . . . . . . . . . . . . . .    41
   What is a swap file?  . . . . . . . . . . . . . . . . . . . . . . . .    41
   How does CacheAll use the swap file?  . . . . . . . . . . . . . . . .    41
   Defining a swap file for CacheAll . . . . . . . . . . . . . . . . . .    42
   Removing the swap file from your hard drive . . . . . . . . . . . . .    43

   Maximizing CacheAll's Performance . . . . . . . . . . . . . . . . . .    44
   What CacheAll version 1.0e will not do  . . . . . . . . . . . . . . .    45
   CacheAll's Automatic Settings . . . . . . . . . . . . . . . . . . . .    46
   Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . .    47
   Common Questions  . . . . . . . . . . . . . . . . . . . . . . . . . .    48
   Notes to CD-ROM Users . . . . . . . . . . . . . . . . . . . . . . . .    50
   Notes to Network Users  . . . . . . . . . . . . . . . . . . . . . . .    51

   AppTrack(TM) Makes Software audits a nuisance rather than a concern .    53

   Reseller Qualification Form: C&D Welcomes Resellers!  . . . . . . . .    54


   CacheAll Evaluation Manual                                           Page 1
   --------------------------------------------------------------------------
   -

                 About CacheAll(tm), The Cache of the 90's!(tm),

        CacheAll is the only technology-independent cache program ever that
   can speed up file access over 1000%! CacheAll is only 21 Kilobytes in size
   and may be loaded high! CacheAll's advanced abilities don't stop there:
   CacheAll is the only cache on the market that does all this -

   1) CacheAll has no limit to the types of devices it can cache,
            Caches CD-ROMs & networked CD-ROMs
            Caches Opticals & networked Opticals
            Caches Hard Drives & networked Hard Drives
            Caches Etc.! & networked Etc.!

   2) CacheAll uses RAM and an optional SWAP FILE for cache data storage
            Supports cache sizes up to 64 Megabytes
            SWAP FILE allows emulation and conservation of expensive RAM
             and,
            Can specify how devices are cached: RAM or SWAP FILE
                - Balances cache performance across slow and fast devices
                - Reduces server loading and network traffic

   3) CacheAll speeds up Microsoft Windows & multimedia,
            CD-ROM applications fly
            And networks too!

   4) CacheAll Increases Network performance when run on WORKSTATIONS **
            64 Megs of server data can be cached locally at workstation
                - Reduces network traffic
                - Reduces server loading
            Artisoft(TM) LANtastic(TM) Compatible

   5) CacheAll allows you to cache specific sections of a resource
            Cache data YOU want to cache, rather than entire device
            Can eliminate the need for cache-locking

   6) CacheAll includes CUtil
            DOS & Windows cache control
            Provides real time viewing of files currently in cache
               -  Excellent "tweaking" & management tool
               -  And, of course, this feature works for network drives
            View statistics, reset statistics, and more

   7) CacheAll can reconfigure itself automatically
            CacheAll can optimize it's own parameters on startup
            CacheAll is user friendly for beginners yet flexible for experts

        CacheAll provides all these features for only $79 (retail $129).
   Hurry, this pricing ends May 31, 1993 but sending in a valid registration
   form before May 31, 1993 from this evaluation software will make you
   eligible for future upgrade prices!

   ** FOR NETWORK DATA BASE USERS ONLY -- To prevent potential loss of your
   data, CacheAll will not cache shared data files which are simultaneously


   CacheAll Evaluation Manual                                           Page 2
   --------------------------------------------------------------------------
   -

   updated by multiple users across a network UNLESS you set these files to
   read only status.


   CacheAll Evaluation Manual                                           Page 3
   --------------------------------------------------------------------------
   -

                    About The Evaluation Version of CacheAll

        This evaluation version is only limited in that it will stop working
   after May 1993.

        Because CacheAll uses new caching techniques, many cache benchmarking
   programs DO NOT accurately detect the presence of CacheAll and therefore
   erroneously report no performance increase! This is simple to prove:
   simply run {your application} without CacheAll and time with a stopwatch,
   then install CacheAll and run {your application} again TWICE measuring the
   time each time. Note that the last time {your application} was run it took
   considerably less time because of CacheAll!

                              How to Order CacheAll

        This abbreviated manual covers only basic CacheAll and CUtil
   operation. This manual is for your evaluation of CacheAll and CUtil,
   should you continue to use CacheAll or CUtil you are required to purchase
   the commercial version of CacheAll:

   If you are an ENDUSER: To purchase C&D products including CacheAll,

      - Visit your favorite software store or computer retailer
      - Call C&D Programming Corp. @ 800-847-5676 (outside U.S. 801-582-0503)
      - CacheAll's price is only $79 through May 1993
      - NOTE:
             Sending in your registration form FROM THIS EVALUATION SOFTWARE
             before May 31, 1993 will make you eligible for future upgrade
             discounts!
      - Please send your registration form to the address noted on the form. 

   If you are a RESELLER: To purchase C&D products including CacheAll,

        Please mail the completed qualification form which appears at the end
   of this document to the noted address, or fax to 801-581-0883. After we
   receive your properly completed qualification form we will send you a
   reseller package which includes information necessary to order all C&D
   products.

                 NO RESELLER INFORMATION WILL BE GIVEN UNTIL WE
                RECEIVE A PROPERLY COMPLETED FORM, NO EXCEPTIONS!


   CacheAll Evaluation Manual                                           Page 4
   --------------------------------------------------------------------------
   -

                   What do you get when you purchase CacheAll?

   1) The commercial software,
              Is not time limited
              Runs WITHOUT having to press any keys on startup.

   2) The commercial software provides:

        for everyone,

              124 pages
              2 colors
              Spiral Bound! (lays flat on a table, desk, etc.)
              Easy to read
              Organized layout
                  - 12 sections
                  - Dictionary like tab bleeds => easy to find desired
                    sections
                  - Fully indexed
                  - Table of contents inside at beginning as you are learning
                  - Quick reference inside back cover for experienced users
              Glossary of terms

        for experienced computer users,

              Details of CacheAll and CUtil operation 
              Performance tips
                  - For options settings
                  - For specific computer configurations
                  - Importance of specific options and settings
              Glossary of terms

   3) Update notices and discounts on future releases


   CacheAll Evaluation Manual                                           Page 5
   --------------------------------------------------------------------------
   -

                      Technical Support -- How to reach us

        Note that after May 31, 1993 a valid registration/serial number will
   be required for all technical support regarding CacheAll! C&D Programming
   Corp. will provide product support to unregistered users only during the
   evaluation period. Please be prepared to give:

         The contents of your AUTOEXEC.BAT and CONFIG.SYS
         A description of your computer including,
             - CPU type and speed
             - Optical drive type and speed
             - CD-ROM type and speed
             - Hard drive type and size
             - Network type and version numbers
             - Type and manufacturer of cards (VGA, etc.)

   to the technician before contacting C&D and include this information with
   all correspondence. You may contact any one of the following sources for
   technical support:

        This Document: Try reading through this manual

        BBS:      (516) 434-8712 for the latest technical tips and the latest
                  versions of utilities, such as CacheAll's CUtil.
                  Modem setup is: 8 data bits, no parity & 1 stop bit
                  Modem speed is: 9600 baud, 38400 with compression

        Phone:    VOICE:    (516) 434-3214
                  FAX:      (516) 434-7603
                  FAXes -- Please remember to include YOUR FAX number!

        Postal:   C&D Programming
                  Technical Support (CAEVAL1.0e)
                  PO Box 1305
                  Brentwood, NY 11717


   CacheAll Evaluation Manual                                           Page 6
   --------------------------------------------------------------------------
   -

                               Welcome to CacheAll

        CacheAll instantly speeds up access to all of your personal
   computer's data. CacheAll, unlike any other cache software available, is a
   technology-independent cache which means it can speed up virtually all
   storage devices! CacheAll can even extend laptop and notebook battery life
   by reducing storage drive usage! CacheAll's advanced features don't stop
   there ... it also automatically detects and efficiently responds to the
   presence of storage devices. Just install CacheAll and without further
   work, sit back and enjoy faster computing!

        When speed is important CacheAll's 1000%+ speed increase also saves
   you money by avoiding costly and difficult upgrades of network drives, CD-
   ROM drives, Optical drives, Bernoulli disks, and Hard drives, assuming an
   upgrade is even available!

        Installed on all network workstations and non-dedicated servers,
   CacheAll can dramatically reduce network traffic and server loading.
   CacheAll accomplishes this by locally caching as much as 64 Megabytes of
   data (Using RAM AND a SWAP FILE!) at the workstation -- after the first
   read, workstations obtain data from CacheAll's local copy instead of
   having to use the network.

        CacheAll operates in the background making fast copies of your data
   in RAM (and an optional SWAP FILE) as you are using your personal
   computer. Thereafter CacheAll immediately provides this copied data and
   eliminates the long access times of CD-ROMs, opticals, networks, etc.
   Using this technique, CacheAll makes your storage devices appear as if
   they have been replaced with faster more expensive models, assuming a
   faster model even exists!

      Congratulations on purchasing CacheAll -- The Cache of the 90's!(TM)


   CacheAll Evaluation Manual                                           Page 7
   --------------------------------------------------------------------------
   -

                           Before Installing CacheAll

   Please take the following steps before installing CacheAll:

      - Please refer to the section entitled "Application Compatibility for
        CacheAll" for important information regarding the use of CacheAll
        with other applications.

      - Have a stamped envelope handy and your printer ready to print so that
        you can immediately print and return the Registration Information
        form. Returning this form entitles you to receive:

              Future upgrade discounts
              New product announcements

                               System Requirements

   Installation Program
      - IBM AT, PS/2, or 100% compatible computer
      - 300Kb of conventional memory during installation
      - MS-DOS versions 3.3 or later; or DR DOS 5.0 or later

   CacheAll and CUtil for DOS
      - Minimum CONFIG.SYS settings of
                 FILES = 40
                 Buffers = 10
      - IBM AT, PS/2, or 100% compatible computer
      - MS-DOS versions 3.3 or later; or DR DOS 5.0 or 6.0
      - When CacheAll is used to cache fast storage devices, such as a hard
        drive:
                 512Kb (minimum) of extended, EMS or XMS allocated to
                  CacheAll
                 300Kb free hard drive space
      - When CacheAll is used to cache slow storage devices, such as CD-ROMs:
                 1Mb (minimum) of Extended Memory allocated to CacheAll
                 4.2Mb of free hard drive space, 300Kb for CacheAll program
                  files plus 4Mb for the recommended swap file
                     - Conventional RAM usage: 21Kb when loaded high using a
                       memory manager; 50 to 150Kb without a memory manager
                       (depending on configuration)

   CUtil for Windows
      - IBM AT, PS/2, or 100% compatible compute
      - Approximately 200Kb of memory while executing
      - MS-DOS versions 3.3 or later; DR DOS 5.0 or 6.0
      - Microsoft Windows Version 3.0+


   CacheAll Evaluation Manual                                           Page 8
   --------------------------------------------------------------------------
   -

                     Application Compatibility for CacheAll

   Microsoft Windows 3.x
        When using CacheAll with Windows, you must load CacheAll before
        starting Windows. If CacheAll is not loaded first, unpredictable
        results may occur. If you are using Windows 3.0, you must also add
        the line InDosPolling=1 to the [386Enh] section of the SYSTEM.INI
        file. Please refer to your Microsoft Windows documentation for the
        procedures to change the SYSTEM.INI file.
    
   Quarterdeck DESQview
        CacheAll must be loaded before DESQview, not under a DESQview task.
        Loading CacheAll in a task may cause unpredictable results.
    
   Artisoft LANtastic
        When loading CacheAll on a LANtastic network, you must load CacheAll
        after all network components; this includes REDIR and SERVER. Loading
        CacheAll before the SERVER may cause unpredictable results.
    
   Novell Netware
        When loading CacheAll on a Netware network, you must load CacheAll
        after the NET component. Loading CacheAll before the NET component
        may cause unpredictable results.
    
   Other networks
        When loading CacheAll on a network, you should load it after all
        network components. Loading CacheAll before the network components
        may cause unpredictable results.

   Street Atlas USA Version 1.0
        Street Atlas USA has a single very large file called WEST.DAT. To
        take full advantage of CacheAll, BLOCKSIZE must be greater than 7. If
        BLOCKSIZE is not greater than 7 only part of WEST.DAT will be cached.

   Disk compression programs
        When using disk compression programs, be sure not to place the swap
        file (specified with the DISKPATH option; see CacheAll options
        section for full details of the DISKPATH option) on a compressed
        volume. If you do put the swap file on a compressed volume,
        unpredictable results may occur. Remember: the effective swap file
        size will change and possibly overflow the volume of a compressed
        drive. For this reason placing any swap file, such as Microsoft's
        Windows swap file, on a compressed should be avoided!

   SCSI Drives
        CacheAll v1.0e does not support double buffering. If you own a SCSI
        drive which requires double buffering, you must run double buffering
        software with CacheAll.

   Silver Platter and other CD-ROM based retrieval systems
        To cache CD-ROMs with CacheAll your software may need to be set for
        networks regardless if CD-ROM is local. Use CUtil's LIST command to
        determine if CacheAll requires this configuration change.  If very


   CacheAll Evaluation Manual                                           Page 9
   --------------------------------------------------------------------------
   -

        few or no files are listed with the CUtil LIST command, you should
        try to have your retrieval system set up as if it is on a network.


   CacheAll Evaluation Manual                                          Page 10
   --------------------------------------------------------------------------
   -

                              Software Installation

        This SECTION takes you step by step through the CacheAll installation
   procedure. CacheAll's installation program is very easy to use since
   CacheAll is a "smart" program which eliminates complicated installation
   procedures:

        Each time your computer is restarted CacheAll analyzes your system
        and reconfigures itself appropriately. This allows you to make future
        changes to your system, including adding CD-ROMs and network drives
        WITHOUT EVER HAVING TO MAKE ANY CHANGES TO CacheAll! Simply install
        and enjoy CacheAll's increase of your systems performance!

        The install procedure consists of a series of display screens which
   are described in the following text. If at any time during the
   installation you are not sure how to answer, simply press ENTER to accept
   the default selection.

                       Preparing Your System For CacheAll

        This section discusses a few tasks which are necessary before
   installing CacheAll.

        It is good practice to backup all of your writable storage devices
   whenever making a change to your system. CacheAll does not harm the
   information contained on these devices but it is good practice to back
   them up in any case. Please refer to your DOS manual for backup
   instructions if you do not already have a method to backup your system.

        If you are currently using a DOS version earlier than DOS 3.3 then
   you will have to upgrade in order to use CacheAll. If you are not using
   DOS 5.0 or later and were thinking of upgrading then do so before
   installing CacheAll to take advantage of the many benefits over previous
   DOS versions, especially memory management facilities which CacheAll will
   take full advantage of.

                                  About INSTALL

        The CacheAll installation program is designed to automatically
   determine your hardware configuration. First it will attempt to determine
   the type of video display you have. Whether you have a monochrome or color
   display, it will automatically adjust to display the best view for that
   particular type of video hardware.

        CacheAll's INSTALL program is "mousable", which means that if a mouse
   is connected to your system, you can use it to make selections within the
   dialog boxes. (If you wish to use your mouse and the mouse cursor does not
   appear when INSTALL has started, it should look like a small square block
   in the upper left hand corner, make sure your mouse driver is properly
   loaded. Refer to the documentation for your mouse regarding the loading
   procedure.) To make selections without the mouse you may move between the
   offered selections by pressing Tab or Shift-Tab followed by the ENTER key.
   You may also use the "hot keys" which are described in the following text.


   CacheAll Evaluation Manual                                          Page 11
   --------------------------------------------------------------------------
   -

        You must have at least 200Kb of conventional memory available before
   running the CacheAll installation program.

                                Starting INSTALL

   Some notes before starting:

      - We assume you are installing CacheAll from your A: drive. If you
        choose to install from another drive simply replace all the following
        references to A: with the proper reference for the drive you are
        using, such as B:.

      - When you see the text ENTER it means to press the Enter key. At any
        time during the installation, the Esc or Escape key will abort the
        installation and return you to the DOS prompt.

      - INSTALL will present you with a sequence of "dialog boxes" which
        allow you to enter necessary information and, make choices as to how
        you wish to proceed to the next dialog box. To move between the
        selections offered by each dialog box you may press Tab or Shift-Tab.
        Press ENTER to accept a selection.

      - To begin the installation of CacheAll, create an installation
        diskette by placing the evaluation software onto a floppy disk and do
        the following:

          1. Put the installation disk into your A: drive.
          2. Type:  A: ENTER
             This will change your default disk drive to the A: drive.
          3. Type:  INSTALL ENTER
             This will execute the installation program for CacheAll

        After you complete step 3, it will take a few moments to start the
   installation program. 

        At this point, you will enter the directory into which you want to
   install the CacheAll files. If you want to accept the default directory of
   C:\CACHEALL, simply press ENTER. If you want a different directory, enter
   it now and press ENTER.

        If the directory you entered does not exist, you will be prompted
   with a dialog box. Note that in some cases it may be necessary to create
   the directory BEFORE running the installation software, although this
   situation is very rare.

        If the directory specified in this dialog box is correct, press the
   ENTER key or press the Y key. If the directory specified in this dialog
   box is not correct, press the N key. When you press the N key, the
   installation program will return you to the screen which asks for the
   installation directory. This will give you another chance to select the
   directory to install CacheAll into.


   CacheAll Evaluation Manual                                          Page 12
   --------------------------------------------------------------------------
   -

        After the installation program creates the selected directory, you
   will be asked if your computer is a standalone computer or is connected to
   a network. If your computer IS NOT connected to a network press Y, press N
   if this computer is connected to a network. Be sure to select YES if you
   are not certain how to answer! 

        After selecting the installation type, INSTALL will display the
   Registration Information dialog box. At this point you should be sure your
   printer is turned on. (If you do not have a printer, you may save this
   information in a file that can be printed later).

        To move between the fields, use Tab to move to the next field and the
   Shift-Tab key to move to the previous field. You must complete all
   requested information (name, company, address 1, address 2, city, state,
   zip, phone, fax). If you do not have a company name or a fax number, you
   may leave those entries blank.

        Once you have completed all fields, you have three choices. You can:
          1. Print out the registration form.
             Press Alt-P (hold down the Alt key and press the letter P).
          2. Save the registration form to disk and print later.
             Press Alt-S (hold down the Alt key and press the letter S). This
             will save the registration information to the file CACHEALL.REG
             in the directory you specified on the first screen of the
             installation program.
          3. Cancel the installation and return to DOS.
             Press Alt-C (hold down the Alt key and press the letter C).  

        If you elect to print the registration form now, you will see a
   dialog box which allows you to select the printer port to print the
   registration form to.

        To select the printer port, use the up and down arrow keys until
   desired printer port is highlighted. If your printer is installed on LPT1:
   (printer port number 1), you can just press Alt-P or ENTER and the
   registration form will be printed. To make "last minute" changes to your
   registration information, you may return to that screen by pressing Alt-C.

   Seal the registration form in an envelope and mail to:

                       C&D Programming Corp.
                       User Registration (CA10EVAL)
                       P.O. Box 1305
                       Brentwood, NY 11717

        Do this right away or, FAX it to us at (516)434-7603 right away!

        While sending the registration form to C&D, the installation program
   will be copying the CacheAll program files to the directory you specified.
   While the files are being copied you will see a status screen which shows
   you how far the installation process has proceeded.


   CacheAll Evaluation Manual                                          Page 13
   --------------------------------------------------------------------------
   -

        You must now decide if you want to update your AUTOEXEC.BAT file. 
   Updating this file, by pressing ENTER, will cause CacheAll to
   automatically start each time you turn your computer on. If you do not
   update the file by pressing ALT-N, CacheAll must be started manually by
   running the RUNCA.BAT file in the CacheAll directory (When starting
   CacheAll manually be sure to do so AFTER all device drivers, redirectors
   and network software is installed!).

        At this point, installation is almost complete. All that remains is
   to review the README.TXT file which contains important information
   regarding CacheAll. INSTALL displays this file for you and allows you to
   scroll through the file by using the arrow keys. Should you wish to view
   this information after the installation program ends, you can use the DOS
   "TYPE", DOS "PRINT" command or the DOS 5.0 "EDIT" command.

        You have now completed the installation of CacheAll, The Cache of the
   90's. By rebooting your computer you will experience the tremendous
   benefits CacheAll provides!


   CacheAll Evaluation Manual                                          Page 14
   --------------------------------------------------------------------------
   -

                          BEGINNERS: CacheAll is SMART!

        CacheAll is very user friendly to beginners. Since unlike other
   programs CacheAll is capable of configuring itself, you just install and
   enjoy it without doing any more work! CacheAll will even automatically
   detect the installation of a new storage device, such as a CD-ROM, hard
   drive, network drive, etc., without your changing CacheAll in any way!

        CacheAll is an especially powerful program which provides many
   features not found in any other program. Because CacheAll is so powerful,
   CacheAll automatically sets it's own options for novice users. When
   changes are made to your system, by you or the programs you run, CacheAll
   will detect these changes and reconfigure itself automatically so that you
   don't have to!

        More advanced users should note that you are always free to override
   one or all of CacheAll's automatic features. Refer to the CacheAll Options
   Section to find out how to make these changes.


   CacheAll Evaluation Manual                                          Page 15
   --------------------------------------------------------------------------
   -

                                Running CacheAll

        The installation program will create a batch file called RUNCA.BAT in
   the directory specified during the installation procedure. This batch file
   contains all the information necessary to run CacheAll and will be called
   by your AUTOEXEC.BAT file (unless you told the installation program not to
   modify your AUTOEXEC.BAT file).

        While customizing certain parameter values for your particular system
   can sometimes lead to increased performance, the average user should find
   the automatic settings to be quite acceptable.

        Note that, depending on how you installed CacheAll RUNCA.BAT will use
   STDALONE.OPT (for standalone installations) or NETWORK.OPT (for network
   installations). When infrequently using a network you may wish to consider
   using a batch file to switch back and forth between the appropriate OPT
   file.

        The section titled CacheAll Options describes all the available
   parameters of CacheAll. Again, it is not necessary to use these parameters
   unless you would like to fine tune the performance of CacheAll.

                               Unloading CacheAll

        CacheAll can be unloaded from memory by running the CACHEALL.EXE
   program with the parameter UNLOAD (or the abbreviation U). To do this you
   must make sure you are in the subdirectory which contains CacheAll. For
   this reason, you may want to consider adding CacheAll to your PATH. For
   example, if you specify the command:

             C:\CACHEALL\CACHEALL UNLOAD

   from the DOS command line, CacheAll will unload itself from memory. Note
   that if CacheAll is not the last program loaded into memory, CacheAll will
   be deactivated but will remain in your system's memory until your computer
   is turned off or rebooted.


   CacheAll Evaluation Manual                                          Page 16
   --------------------------------------------------------------------------
   -

                                CacheAll Options

        Spaces are not allowed, except between options. Example valid command
   lines are:

             CACHEALL MEMSIZE=8192 BLOCKSIZE=4 VERBOSE
             CACHEALL MS=8192 BS=4 V

   These lines are identical in CacheAll and signify a memory size of 8192Kb
   (MEMSIZE=8192 or MS=8192) and a block size of 4096 bytes (BLOCKSIZE=4 or
   BS=4). It will also show all CacheAll settings upon startup (VERBOSE or
   V).
   NOTE: Numeric parameters always signify kilobytes.

             CACHEALL MEMSIZE=4000 BLOCKSIZE=4 DISKSIZE=5000
             CACHEALL MS=4000 BS=4 DS=5000

   These lines are identical in CacheAll and signify a memory size of 4000Kb
   (MEMSIZE=4000 or MS=4000), a disk size of 5000Kb (DISKSIZE=5000 or
   DS=5000) and a block size of 4096 bytes (BLOCKSIZE=4 or BS=4).
   NOTE: Numeric parameters always signify kilobytes.

        Options which have a value after the equal sign must not include
   spaces around the equal sign. Adjacent options must have at least once
   space separating them.

        You can create an option file to store your most commonly used
   parameters. See the section titled Creating a CacheAll Option File for
   full details.

        The next several pages detail each of CacheAll's command line
   options. Each page consists of the option name in large bold characters
   followed by a series of sections describing the option.


   CacheAll Evaluation Manual                                          Page 17
   --------------------------------------------------------------------------
   -

   ALLFILES
                   ** USE THIS OPTION WITH EXTREME CAUTION! **
        Shortcut: AF

        Example:  ALLFILES=C-ER
                  This will tell CacheAll to cache all files on drives C
                  through E (C,D,E), and R.

        Default:  CacheAll automatically sets this option for all local
                  CD-ROM drives.

        Details:  If this option is set on a networked drive, loss of data
                  can occur on that drive! Example: Using 2 networked
                  personal computers as an example, if PC 1 reads some part
                  of a file (which then becomes cache data in CacheAll) just
                  before PC 2 writes to the same file, CacheAll's cache data
                  on PC 1 does not reflect the file changes made by PC 2!

        Notes:    It may be necessary to manually set this option when using
                  CD-ROMs over a network.

   BLOCKSIZE
        Shortcut: BS

        Example:  BLOCKSIZE=4
                  This will tell CacheAll to use a 4Kbytes block size for
                  managing its internal cache.

        Default:  Automatically chosen to minimize overall memory usage.

        Notes:    Setting BLOCKSIZE to it's maximum value of 16 WILL NOT
                  necessarily give maximum CacheAll performance! To tweak
                  this option, slowly raise and lower BLOCKSIZE setting until
                  maximum performance is achieved.


   DISKPATH
        Shortcut: DP

        Example:  DISKPATH=D:\TEMP
                  This will tell CacheAll that you want the disk cache swap
                  file to be stored in the TEMP directory on the D drive.

        Default:  C:\ is the default path.

        Details:  Place the swap file on a local hard drive and avoid
                  compressed disks (such as a Stacker volume) and network
                  drives since loss of data may result.


   CacheAll Evaluation Manual                                          Page 18
   --------------------------------------------------------------------------
   -

   DISKSIZE
        Shortcut: DS

        Example:  DISKSIZE=6000
                  This will tell CacheAll to use 6000 Kilobytes (Kb)  (6
                  Megabytes) for its swap file.

        Default:  Automatically chosen based on free disk space -- equal to
                  50% of free disk space up to 4 Megabytes.

        Choices:  Any number from 0 through 64000.

        Notes:    MEMSIZE + DISKSIZE can not exceed 64 Megabytes.

   DRIVES
        Shortcut: D

        Example:  DRIVES=FN-PR-T
                  This will tell CacheAll to cache only drives F, N through P
                  (N,O,P) and R through T (R,S,T).

        Default:  All non-removable drives found in your system are cached
                  (as determined at startup of CacheAll).

        Choices:  Any drive letters from A through Z.

        Details:  Even if you use one of the other drive selection options
                  (ALLFILES or FAST), you must still specify the drive letter
                  using the DRIVES option. You can think of the DRIVES option
                  as the "complete set of drives which CacheAll will cache."

        Notes:    Removable drives, such as floppies, will not be cached by
                  CacheAll unless you specifically tell CacheAll to do so
                  with the DRIVES option. CD-ROMs are not considered to be
                  removable.

   FAST
        Shortcut: F

        Example:  FAST=C-EM
                  This will tell CacheAll not to use the swap file to cache
                  drives C through E (C,D,E) and M.

        Default:  All local drives found in your system, except CD-ROMs, are
                  treated as FAST.

        Choices:  Any drive letters from A through Z.

        Details:  Properly setting FAST helps avoid the potentially wasteful
                  situation of caching a hard drive to the swap file and
                  dedicates your swap file to slower (relative to the drive
                  upon which the swap file is placed) storage devices such as
                  CD-ROMs and network drives.


   CacheAll Evaluation Manual                                          Page 19
   --------------------------------------------------------------------------
   -

   HELP
        Shortcut: H or ?

        Example:  HELP

        Details:  This option causes CacheAll to show the help screen listing
                  all available CacheAll options.

   MAXFILES
        Shortcut: MF

        Example:  MAXFILES=200
                  This tells CacheAll to keep cache information for a maximum
                  of 200 files.

        Default:  This option varies depending on the cache sizes specified
                  in MEMSIZE, DISKSIZE, and BLOCKSIZE.

        Choices:  Number must be equal to or greater than the number of FILES
                  specified on the FILES= line in your CONFIG.SYS (we suggest
                  setting FILES=30 and BUFFERS=10 if no such lines appear in
                  your CONFIG.SYS). This option is allowed a maximum value of
                  400 files.

   MEMSIZE
        Shortcut: MS

        Example:  MEMSIZE=2048
                  Tells CacheAll to use 2048 Kilobytes (Kb) or 2 Megabytes
                  (Mb) for its memory cache.

        Default:  Automatic memory cache size is 25% of your available
                  Extended, XMS or EMS. CacheAll will search in that order,
                  and will take 25% of whichever memory it finds first.
                  CacheAll may be forced to use a specific memory type using
                  the MEMTYPE option.

        Choices:  Any number from 64 through 64000.

        Notes:    MEMSIZE + DISKSIZE can not exceed 64 Megabytes.


   CacheAll Evaluation Manual                                          Page 20
   --------------------------------------------------------------------------
   -

   MEMTYPE
        Shortcut: MT

        Example:  MEMTYPE=EXTENDED
                  Tells CacheAll to use extended memory for the memory cache.

        Default:  CacheAll will search for all types of memory. It will
                  search memory types in this order:
                    1. extended
                    2. XMS
                    3. EMS
                  The first memory type found will be used to satisfy the
                  MEMSIZE setting.

        Choices:  The available choices are EXTENDED, XMS and EMS.

        Details:  If you are not using a memory manager, such as QEMM or
                  EMM386, you will be forced to use extended memory since no
                  other memory type is available.

   MPX
        Shortcut: MPX

        Example:  MPX=C8
                  This specifies a multiplex id of C8.

        Default:  CacheAll will search for the first available multiplex id
                  starting from C0.

        Choices:  The valid choices are C0 through FF (it is specified as a
                  hexadecimal number).

        Details:  Other applications, such as Microsoft Windows, use the
                  multiplex id extensively and if a multiplex id conflict
                  does occur, this is how you would change it.

   SMALLFILES
        Shortcut: SF

        Example:  SMALLFILES=Y

        Default:  Y is the default for this option.  

        Choices:  The available choices are Y to have CacheAll cache all
                  small files or N to have CacheAll ignore all small files.

        Details:  If use have an application which opens many small files
                  only once (such as Norton Desktop for Windows or Microsoft
                  Windows), you might want to set SMALLFILES=N. CUtil's LIST
                  command can be used to determine if small files are
                  monopolizing the cache and so SMALLFILES should be set to
                  N.


   CacheAll Evaluation Manual                                          Page 21
   --------------------------------------------------------------------------
   -

   UNLOAD
        Shortcut: U

        Example:  UNLOAD
                  Tells CacheAll to remove itself from memory.

        Details:  This option is used to unload CacheAll from memory. If
                  CacheAll was not the last program loaded into memory, it
                  will be disabled but not removed from memory. In either
                  case, CacheAll will stop caching data.

   VERBOSE
        Shortcut: V

        Example:  VERBOSE
                  Tells CacheAll to report the value of all options after
                  startup.

        Default:  This option is turned off by default

        Details:  This option causes CacheAll to display all of the option
                  settings when it starts up.

   @
        Shortcut: There is no shortcut for this option since it is only one
                  character.

        Example:  @CACHEALL.OPT
                  This will tell CacheAll to read its options from the file
                  CACHEALL.OPT in the current directory.

        Details:  This option allows you to specify the filename of an option
                  file which will provide the desired options settings for
                  CacheAll instead of their being typed on the command line.
                  In some cases this option will be a convenience, in other
                  cases an option file must be created because the command
                  line will not provide enough space to enter all the
                  necessary options. For full details on creating an option
                  file, see the section titled Creating a CacheAll Option
                  File.


   CacheAll Evaluation Manual                                          Page 22
   --------------------------------------------------------------------------
   -

   ;
        Shortcut: There is no shortcut for this option since it is only one
                  character.

        Example:  ; This is a comment
                  The above represents a comment section of a line in an
                  option file.

        Default:  There is no default for this option.

        Details:  This option allows comments to be placed in your option
                  file. When processing an option file the semicolon and all
                  characters following it on a line are ignored. It is
                  acceptable to place comments on the same line as option
                  settings so long as the comments are placed after (to the
                  right of) the option setting on that line. For full details
                  on creating an option file, see the section titled Creating
                  a CacheAll Option File.


   CacheAll Evaluation Manual                                          Page 23
   --------------------------------------------------------------------------
   -

                              CacheAll Option File

        CacheAll allows the use of an option file to specify the settings of
   it's options. The option file is a DOS TEXT file which contains a list of
   option settings for the CacheAll program. The CacheAll option file makes
   it easy to maintain a list of custom parameters. These files can be
   created with any text file editor such as DOS's EDLIN or EDIT (for DOS
   5.0+ users). The following is a sample option file: 

             ; Sample CacheAll Option file
             DRIVES=A-Z
             FAST=C-EG
             AF=R      ; This option tells CacheAll to cache ALL files on R:
             MS=4000   ; This option tells CacheAll to use 4000Kb for the
                       ; cache.
             DS=8000
             ; The below option tells CacheAll to display complete startup
             ; info
             VERBOSE

   Key points to notice in the example above: 

           - Comments may be used anywhere as long as a semi-colon is placed
             before the comment text.
           - Both full commands and abbreviations can be used 
           - Only one option may be specified per line.  If you specify more
             than one option per line, an error will result. 

   To use an option file, run CacheAll as follows:

                  CACHEALL @C:\CACHEALL\CACHEALL.OPT 

        This command line will load CacheAll with an option file called
   C:\CACHEALL\CACHEALL.OPT. The @ followed by a filename tells CacheAll to
   read all the options from that file.


   CacheAll Evaluation Manual                                          Page 24
   --------------------------------------------------------------------------
   -

                             CacheAll Error Messages

   BLOCKSIZE must be between 2-16.
        Reason:   Occurs when you specify a BLOCKSIZE outside the valid range
                  for BLOCKSIZE.
        Solution: Let CacheAll decide on the optimal BLOCKSIZE or choose a
                  value which is between 2 and 16, inclusive.

   CacheAll is already installed.
        Reason:   Occurs when you try to load CacheAll after CacheAll has
                  already been loaded. CacheAll will not load itself more
                  than once.
        Solution: If you want to reconfigure the parameters, use the UNLOAD
                  option to remove CacheAll from memory (the UNLOAD option
                  will release memory if CacheAll was the last
                  memory-resident program loaded, therefore remove other
                  programs before UNLOADing CacheAll) then "reload" (rerun)
                  CacheAll with the desired option settings.
        Notes:    Do not try to unload CacheAll from within Windows, a DOS
                  shell or other operating environment. Doing so may cause
                  your system to "hang".

   CacheAll is not installed!
        Reason:   Occurs when an error occurs during the startup of CacheAll.
        Solution: If you see this message, there are probably other error
                  messages shown. Refer to this section for details on the
                  other error messages. Once you fix the other errors this
                  error should disappear.

   Cache exceeds max allowable pages. Cache truncated. To use a larger cache
   increase the BLOCKSIZE.
        Reason:   Occurs when MEMSIZE and DISKSIZE are too large for the
                  specified BLOCKSIZE.
        Solution: Do not specify a BLOCKSIZE, let CacheAll automatically
                  choose a block size for acceptable values of MEMSIZE and
                  DISKSIZE values.
        Notes:    If you want to know complete details, refer to the
                  commerical CacheAll manual.

   Drive x is not valid
        Reason:   Occurs when swap file is placed on an invalid drive.
        Solution: Check the DISKPATH option to ensure the pathname specified
                  is valid.


   CacheAll Evaluation Manual                                          Page 25
   --------------------------------------------------------------------------
   -

   EMS driver is not responding. Tables will be in real memory.
        Reason:   Occurs when CacheAll cannot find any EMS memory.
        Solution: To provide EMS memory, a memory manager such as QEMM or
                  EMM386 must be installed.
        Notes:    Lack of EMS memory will not affect CacheAll's operation but
                  additional conventional memory will be used. When using a
                  memory manager CacheAll will take as little at 22Kb of
                  conventional memory, and can be loaded high.

   Error (xxx) reading parameter file!
        Reason:   Occurs when CacheAll cannot read the option file specified
                  with the @ option. The xxx will be replaced by the DOS
                  error when CacheAll attempted to open and read the file.
                  The most common errors will be 2 (File not found) or 5
                  (Access denied).
        Solution: Check the filename specified for the option file to ensure
                  that it is valid and that CacheAll has exclusive access to
                  it (ie. be sure the file is not being used by another
                  network user).

   Error allocating cache pages.
        Solution: Contact C&D Programming's technical support staff.

   Error allocating file list.
        Solution: Contact C&D Programming's technical support staff.

   Error allocating EMS memory.
        Reason:   Occurs when CacheAll is told to use EMS memory but CacheAll
                  cannot find such memory.
        Solution: Try using another type of memory (by using the MEMTYPE
                  option) or ensure that a memory manager is properly loaded
                  and providing EMS memory.

   Error finding page frame.
        Solution: Contact C&D Programming's technical support staff.

   Incorrect DOS Version! Need DOS 3.30 or above.
        Reason:   Occurs when trying to run CacheAll using a version of DOS
                  before version 3.30.
        Solution: Upgrade to DOS 3.3 or higher.

   Invalid option 'xxx'
        Reason:   Occurs when an invalid option is specified on the command
                  line or in the option file.
        Solution: Check the command line parameters you have entered and try
                  running CacheAll again. When using an option file, be sure
                  all options within the file are valid and all comment lines
                  are prefixed with a semi-colon.


   CacheAll Evaluation Manual                                          Page 26
   --------------------------------------------------------------------------
   -

   Minimum files being allocated in REAL memory.
        Reason:   Occurs when CacheAll cannot fit all of its internal tables
                  into EMS memory.
        Solution: Let CacheAll automatically choose the BLOCKSIZE value.
        Notes:    When specifying a very large cache, greater than 40Mb,
                  raising the value of BLOCKSIZE will probably not eliminate
                  this error and in this case the error may be ignored. If
                  the desired cache size is less than 40Mb, CacheAll will
                  choose a BLOCKSIZE which will place all internal tables
                  into EMS.

   Must have a MEMSIZE of at least 64.
        Reason:   Occurs when MEMSIZE is specified to be less than 64.
        Solution: Only use MEMSIZE settings from 64 to 64000 or let CacheAll
                  choose the MEMSIZE automatically.

   Multiplex Id xxx is already in use.
        Reason:   Occurs when the specified MPX is already in use.
        Solution: Let CacheAll choose the MPX value automatically. In most
                  cases CacheAll will choose an MPX which is available and
                  does not conflict with other software.

   Multiplex Id must be between C0-FF.
        Reason:   Occurs when a multiplex id (specified with the MPX option)
                  is outside the valid range of C0 through FF.
        Solution: Let CacheAll choose its own MPX or respecify the MPX
                  between the C0 through FF range, as a hexadecimal number.

   No available Multiplex Ids.
        Solution: Contact C&D Programming's technical support staff.

   No Room in EMS page frame for ID Buffer.
        Reason:   Occurs when CacheAll cannot fit all of its internal tables
                  into EMS memory.
        Solution: Let CacheAll automatically choose the BLOCKSIZE value.
        Notes:    When specifying a very large cache, greater than 40Mb,
                  raising the value of BLOCKSIZE will probably not eliminate
                  this error and in this case the error may be ignored. If
                  the desired cache size is less than 40Mb, CacheAll will
                  choose a BLOCKSIZE which will place all internal tables
                  into EMS.

   No swap file!! Error (xxx)
        Reason:   Occurs when CacheAll cannot create a swap file.
        Solution: Be sure the pathname specified in the DISKPATH option is
                  valid and enough disk space is available for the value
                  specified in the DISKSIZE option.


   CacheAll Evaluation Manual                                          Page 27
   --------------------------------------------------------------------------
   -

   Not enough room in EMS page frame for File List.
        Reason:   Occurs when CacheAll cannot fit all of its internal tables
                  into EMS memory.
        Solution: Let CacheAll automatically choose the BLOCKSIZE value.
        Notes:    When specifying a very large cache, greater than 40Mb,
                  raising the value of BLOCKSIZE will probably not eliminate
                  this error and in this case the error may be ignored. If
                  the desired cache size is less than 40Mb, CacheAll will
                  choose a BLOCKSIZE which will place all internal tables
                  into EMS.

   Not enough room in EMS page frame for Handle List.
        Reason:   Occurs when CacheAll cannot fit all of its internal tables
                  into EMS memory.
        Solution: Let CacheAll automatically choose the BLOCKSIZE value.
        Notes:    When specifying a very large cache, greater than 40Mb,
                  raising the value of BLOCKSIZE will probably not eliminate
                  this error. If the desired cache size is less than 40Mb,
                  CacheAll will choose a BLOCKSIZE which will place all
                  internal tables into EMS.

   Out of Disk Space. Swap file has been disabled.
        Reason:   Occurs when CacheAll determines there is not enough disk
                  space to create a swap file.
        Solution: You should free some disk space for the swap file or
                  designate a smaller swap file with the DISKSIZE option.

   Out of  Memory!! Error (xxx)
        Reason:   Occurs when CacheAll can not allocate enough memory to
                  satisfy the options specified.
        Solution: Free up some memory (extended, EMS, or XMS) and try running
                  CacheAll again. If possible add more memory to your
                  computer. If neither of these solutions work, lower the
                  value specified with MEMSIZE.

   Warning!!! swap file drive is not a local hard disk. This may result in
   slower response times.
        Reason:   This error message occurs when the DISKPATH option points
                  to a drive which is not local (such as a network drive).
        Solution: No change is necessary. This is only a warning message. If
                  you want to get the greatest performance from CacheAll, you
                  should put the swap file on the fastest storage device you
                  have available (usually your local hard drive).

   You may have a maximum of xxx files. Decreasing files.
        Reason:   Occurs when MAXFILES is specified to be greater than 400.
        Solution: Reduce MAXFILES setting to less than 400.


   CacheAll Evaluation Manual                                          Page 28
   --------------------------------------------------------------------------
   -

                             CUtil(TM) Introduction

        CUtil, which stands for CacheAll Utility, provides an interface to
   the CacheAll program. CUtil is used to view and control CacheAll's
   operation. CUtil provides the following:

        - Display of CacheAll statistics, such as Read Hit Rate, etc.
        - Resetting CacheAll statistics
        - Flushing CacheAll's cache
        - Display current CacheAll parameters
        - Modification of certain CacheAll parameters
        - Enabling and disabling the swap file
        - View which files CacheAll is caching and to what efficiency

        Just as we have made CacheAll easy to use by giving it the power to
   automatically examine your system and set it's own parameters, CUtil
   automatically detects whether it is run under DOS or Windows and provides
   a different operating mode for each.    In the following section, the DOS
   and Windows modes of CUtil will be discussed.


   CacheAll Evaluation Manual                                          Page 29
   --------------------------------------------------------------------------
   -

                                  CUtil for DOS

   The DOS mode of CUtil has several command line parameters which are:

             FLUSH
                  Flushes specified drives from CacheAll's memory

             HELP
                  Displays a short help screen of the command line options

             LIST
                  Displays the list of files which are currently being cached
                  by CacheAll, and the hit rate for each file

             PARAMS
                  Displays the current parameters for CacheAll

             RESET
                  Resets the CacheAll's statistics

             STATS
                  Displays the current CacheAll statistics (this option is
                  assumed when no options are specified)

             SWAPFILE
                  Allows enabling or disabling of CacheAll's swap file

   Note that if no parameter is specified on the command line the STATS
   parameter is assumed.


   CacheAll Evaluation Manual                                          Page 30
   --------------------------------------------------------------------------
   -

                                  CUtil Options

        The next section describes all the options that CUtil supports. These
   command line options are valid only when CUtil is running in DOS mode. In
   Windows mode CUtil uses menus to implement the available options.  Windows
   mode is documented in the section titled "CUtil for Windows."  Unlike
   CacheAll, CUtil allows only one option on its command line.  Some example
   command lines are:

             CUTIL FLUSH=D-G
             CUTIL F=D-G

        These lines are identical in CUtil. They tell CUtil to flush all
   cache data for drives D through G, (drives D:, E:, F:, G:).

             CUTIL PARAMS
             CUTIL P

        These lines are identical in CUtil. They tell CUtil to display the
   current value of CacheAll's options. Note that options which have a value
   after the equal sign must not include spaces around the equal sign. Note
   that if no option is specified on CUtil's command line then CUtil will
   assume the STATS option is desired.

        The next several pages detail each of CUtil's command line options.
   Each page consists of the option name in large bold characters followed by
   a series of sections describing the option.


   CacheAll Evaluation Manual                                          Page 31
   --------------------------------------------------------------------------
   -

   FLUSH
        Shortcut: F

        Example:  F=CE-G
                  This command will flush cache data originating from drives
                  C:, E:, F:, and G:.

        Choices:  Any drive letter from A through Z. To specify all drives a
                  wildcard of * is also allowed.

        Details:  To flush all cache data specify the command line as:

                    F=*  or   FLUSH=* 


   HELP
        Shortcut: H or ?

        Example:  HELP
                  This command will display a short help screen which lists
                  all the commands CUtil supports.

   LIST
        Shortcut: L

        Example:  LIST

        Details:  This command will display the list of files which are
                  currently being cached by CacheAll along with the following
                  information for each file,
                    1) number of bytes read while file was in the cache
                    2) hit rate, percentage of requested bytes read from
                       cache.
                    3) size in bytes
                    4) filename (including complete path)

   PARAMS

        Shortcut: P

        Example:  PARAMS
                  This command will display the current value of CacheAll
                  options.

        Details:  All CacheAll command line options will be displayed.
        


   CacheAll Evaluation Manual                                          Page 32
   --------------------------------------------------------------------------
   -

   RESET
        Shortcut: R

        Example:  RESET
                  This command will reset the CacheAll's statistics.

        Details:  The statistics which are reset are Read Requests, Read
                  Hits, and Read Hit Rate.

   STATS
        Shortcut: S

        Example:  STATS
                  This command will show the current statistics for CacheAll.

        Details:  If you run CUtil for DOS without specifying any command
                  line options, the STATS option is assumed.

   SWAPFILE
        Shortcut: S

        Example:  SWAPFILE=E
                  This command will enable the swap file.

        Choices:  The available choices are E for enabling swap file and D
                  for disabling swap file.

        Details:  This option allows you to enable and disable the use of the
                  swap file "on the fly". Occasionally you might run into an
                  application which is time-critical, such as full motion
                  video. If time is taken to write data to the swap file,
                  your time-critical application might not work as desired.
                  In this case, you can leave CacheAll running, but disable
                  all the swap file activity. Another way to eliminate
                  possible undesirable effects is to be sure to place the
                  swap file on your fastest drive.

        Notes:    If a DISKSIZE of zero was specified on the CacheAll command
                  line, this option cannot be used.


   CacheAll Evaluation Manual                                          Page 33
   --------------------------------------------------------------------------
   -

                                CUtil for Windows

        CUtil for Windows takes advantage of Microsoft Windows by providing
   graphical option settings and a "real-time" statistics display. With CUtil
   you can see CacheAll in action while you read and write to your cached
   drives! To add CUtil's icon to Windows, follow the steps below. These
   instruction assume the default directory settings were chosen during the
   installation procedure, if you didn't make this selection then you must
   specify the directory in which CacheAll is installed:

             - If you are in the Windows environment:
                    1) Activate the Program Manager window
                    2) Select the File menu.
                    3) Select the Run option.
                    4) Type:     C:\CACHEALL\MAKEGRP
                    5) Click on the OK button.
                    6) Once MAKEGRP starts, just follow the on-screen
                       prompts.

             - If you are not running Windows:
                    1) Execute the following command from the DOS prompt
                       while in your windows directory:

                            WIN C:\CACHEALL\MAKEGRP

                    2) Press ENTER
                    3) Once MAKEGRP starts, just follow the on-screen
                       prompts.


                           Executing CUtil for Windows

        When CUtil is executed under Windows the current CacheAll statistics
   will be displayed. Each field of this display gives important information
   about the current state of CacheAll. These fields are summarized below:

   - Memory Total
        The total cache memory CacheAll has allocated. This number is
        specified by the MEMSIZE option on the CacheAll command line. If you
        do not specify the option, CacheAll will automatically choose a
        value.

   - Memory Avail
        The amount of memory left for use by CacheAll. This number will
        always be less than or equal to Memory Total. The amount of memory in
        use would be Memory Total minus Memory Avail.

   - Disk Total
        The size of the swap file on your disk. This number is specified by
        the DISKSIZE option on the CacheAll command line. If you do not
        specify DISKSIZE, CacheAll will automatically choose a value.


   CacheAll Evaluation Manual                                          Page 34
   --------------------------------------------------------------------------
   -

   - Disk Avail
        The amount of swap file space left for use by CacheAll. This number
        will always be less than or equal to Disk Total. The amount of swap
        file space in use would be Disk Total minus Disk Avail.

   - File Total
        The maximum number of files CacheAll can manage at one time. This
        number is specified by the MAXFILES option on the CacheAll command
        line. If you do not specify the option, CacheAll will automatically
        choose a value.

   - File Avail
        The number of file slots available for use by CacheAll. If this
        number goes to zero (or close to zero) you may want to specify a
        larger value for the MAXFILES option to increase performance.

   - Read Requests
        Number of bytes which were read through CacheAll. This includes reads
        from all drives specified in the CacheAll DRIVES command line option.
        If you do not specify the DRIVES option, CacheAll will intelligently
        select which drives to cache.

   - Read Hits
        When some data is requested which is already stored in the cache
        memory, it is called a hit. The Read Hits value represents the number
        of bytes which were read from the data cached by CacheAll. The closer
        this value is to the Read Requests value, the more CacheAll is
        increasing your performance.

   - Read Hit Rate
        The percentage of read hits. This is simply the Read Hits divided by
        the Read Requests. The closer this value is to 100%, the more
        CacheAll is increasing your performance.


                           CUtil for Windows File Menu

   - Exit
        Exit is included for compatibility with all other Windows
        applications (and for those of you that are used to pressing Alt-F
        then X to exit a Windows program). Selecting Exit will cause the
        CUtil session to be closed, you may also use Alt-X to exit CUtil for
        Windows.


   CacheAll Evaluation Manual                                          Page 35
   --------------------------------------------------------------------------
   -

                         CUtil for Windows Options Menu

        The Options menu contains most of the "good stuff" which CUtil can
   do. Each option is discussed in detail on the following pages.

   - Select Drives to Flush...
        This option will show a dialog box with a check box for each drive. 
        You can select the drives you want to flush by clicking next to or on
        top of the desired drive letter. When you are through selecting
        drives, click on the "OK" button. If you decide not to flush any
        drives, press the "Cancel" button. If you want to clear all your
        drive selections, you can use the "Clear All" button. If you want to
        select all the drives, you can use the Select All button. If you want
        to flush all the drives, you should use the "Flush All Drives"
        option, since it is easier to select.

   - Flush All Drives
        Choosing Flush All Drives results in a conformation box. This option
        will flush all cache data from the cache but before doing so you will
        be asked if you really want to flush all data. If you click on the
        Yes button, all cache data will be flushed. If you click on the No
        button, you will return to CUtil with all cached data still in
        CacheAll.

   - Reset Statistics
        This option will reset the statistics which CUtil displays. This is
        useful if you want to see how much CacheAll improves the execution of
        a specific application. The information which is reset is the Read
        Requests, Read Hits, and Read Hit Rate.

   - Parameters
        This option allows you to see, but not change, CacheAll's current
        settings. When you select this option, you will see a dialog box
        outlining each CacheAll option and its current value (Notice that
        each option displayed in this dialog box refers to an option used on
        the CacheAll command line).

        For the items which appear in the "Drive Selection" group box, you
        will notice buttons which say "Click here to view". When you click on
        one of these buttons a dialog box is displayed along with the
        currently selected drives for that option.

   - Swap File Active
        The Swap File option will be in either of two states, active (on) or
        inactive (off). This option will either activate or deactivate the
        use of the swap file by CacheAll. If a small checkmark appears next
        to the menu option, that means the swap file is active, and when
        CacheAll decides data needs to be pushed from cache memory into the
        swap file, it will do so. If there is no checkmark next to the menu
        option, CacheAll will behave as if no swap file was defined.

        Why would you want to disable the swap file? If a swap file is being
        used by CacheAll, the drives not specified by the FAST option will be


   CacheAll Evaluation Manual                                          Page 36
   --------------------------------------------------------------------------
   -

        cached to the swap file. If you are also running a time sensitive
        application from one of these "slow" drives then the added delay of
        CacheAll writes to the swap file may be undesirable. Disabling the
        swap file will stop the added delay of the writes to the swap file.
        You may also wish to consider placing the swap file on a faster drive
        to reduce the delay instead of disabling the swap file.

   - Refresh Rate
        This option allows you to change the update rate of CUtil's
        statistics display. The default rate is once every 5 seconds, and you
        may choose a value from 1 to 60 seconds.


                           CUtil for Windows Help Menu

   - About
        This box shows version and copyright information.

   - Product Support
        Choosing Product Support will show you information on how to get
        product support, including C&D Programming Corp.'s telephone number. 
        This dialog box will also show your serial number and the name you
        entered during the installation process.


   CacheAll Evaluation Manual                                          Page 37
   --------------------------------------------------------------------------
   -

                            Technical Specifications

                                   Benchmarks

        Tests 1 & 2 are network drive benchmarks using the industry standard
   PC Magazine LAN Labs Benchmark Version 3.03 with a one megabyte file size
   test (All numbers are megabits per second), 2 Meg RAM cache and 0 Meg swap
   file. Although not included, similar performance increases from local hard
   drives have been measured. Test 3 shows CD-ROM benchmark results using
   Aris Entertainment's MPC Wizard CD-ROM test. (All numbers are kilobytes
   per second).

          1) The setup for test 1 was a 386/40Mhz PC workstation connected
             with an Artisoft AE-2 Ethernet adapter to a 486/33Mhz LANtastic
             Server. This test shows CacheAll to improve the workstation's
             network drive access speed by 411%.

          2) The setup for test 2 was a 386/25Mhz PC workstation connected
             with a Xircom PE10B2-32K parallel port adapter to a 486/33Mhz
             LANtastic Server. This test shows CacheAll to improve the
             workstation's network drive access speed by 1759%.

          3) The setup for test 3 was a 386/25Mhz PC with a local Mitsumi
             CD-ROM drive (600 millisecond seek time and 150Kbytes/sec
             sustained throughput). This test shows CacheAll to improve the
             PC's local CD-ROM access speed by 2607%.

                                   Cache Size

        A maximum cache size of 64 Megabytes can be implemented. The 64
   Megabytes may be implemented totally in RAM, almost totally in a swap file
   (minimum MEMSIZE setting is 64 Kilobytes) or, may be partitioned between
   RAM and a swap file.

                                Operating Systems

        MS-DOS 3.3+ and  DR DOS 5.x+ are supported.

                             Operating Environments

        DOS, Windows 3.0 and 3.1 and DESQview are supported.

                          Microprocessor Compatibility

        80286, 80386, 80486 and all 100% compatibles are supported.


   CacheAll Evaluation Manual                                          Page 38
   --------------------------------------------------------------------------
   -

                                  Program Size

        The program size for CacheAll varies depending on the parameters used
   at startup. In general, when CacheAll is loaded using a memory manager
   (such as Quarterdeck's QEMM or DOS 5.0+'s EMM386) which provides EMS
   memory, CacheAll will use 22Kb of conventional and 96Kb of EMS. Loading in
   the presence of a memory manager is the recommended configuration. If you
   do not have a memory manager, CacheAll will use from 59Kb to 159Kb of
   conventional memory depending on the configuration. To eliminate
   conventional memory usage, CacheAll can be loaded high, using a memory
   manager.


   CacheAll Evaluation Manual                                          Page 39
   --------------------------------------------------------------------------
   -

                     Caching only specific drive directories

        Through the use of DOS's substitute command ("SUBST.EXE") CacheAll
   may be configured to cache only part of a drive. Use CUtil's LIST command
   to determine which drive directories will benefit most by caching. Next,
   use DOS to substitute an unused drive letter for the directory to be
   cached. By caching the substituted drive and not the original drive, you
   focus the caching resources on files which will show the most benefit when
   cached. Be sure to properly set the LASTDRIVE option inside CONFIG.SYS to
   create "free" drive letters.

   Example:  You wish to cache your entire D: drive but only the "MYSTUFF"
             directory of your C: drive. One method would be:

          1) Include the line,
                  LASTDRIVE=E
             in your CONFIG.SYS

          2) Include the line,
                  SUBST E: C:\MYSTUFF
             before the call to CacheAll in your AUTOEXEC.BAT

          3) Use the following line in your CacheAll OPT file,
                  DRIVES=DE

          4) Use the MYSTUFF directory from the E: you have just created

   Since CacheAll will "not cache" the C: drive but will cache the E: drive
   you effective will cache only the MYSTUFF directory of the C: drive by
   accessing the MYSTUFF directory via the E: drive. In other words, do not
   bother accessing the C:\MYSTUFF directory because it will not be cached,
   access the E: drive instead because the E: drive will be cached.

        Some application cannot be broken up into multiple directories or
   across multiple drives. Therefore it may be necessary to cache their
   entire directory and not just an isolated few files within the directory.


   CacheAll Evaluation Manual                                          Page 40
   --------------------------------------------------------------------------
   -

                       Using CacheAll to Speed up Networks

        Installed on all network workstations and non-dedicated servers,
   CacheAll can dramatically reduce network traffic and server loading.
   CacheAll accomplishes this by locally caching as much as 64 Megabytes of
   data (Using RAM AND a SWAP FILE!) at the workstation -- after the first
   read, workstations obtain data from CacheAll's local copy instead of
   having to use the network. In the following example, workstations will
   accumulate local copies of server data, and therefore will no longer need
   to go through the network to the server to acquire frequently used data.
   This situation is shown in the diagrams below:

        Workstation's first access of specific server data:
                  Ŀ            Ŀ
                        WORKSTATION (WS)               NETWORK SERVER
                  Ŀ   Ŀ   Ĵ  Network   Ŀ   Ĵ
                   WS <->CacheAll<->NOS<---------->NOS<->Hard  
                  Apps    cache         connection       Drive 
                              
        Notice that to initially acquire the needed data the following data
        path must be taken:
               1. CacheAll monitors application's data request
               2. Workstation Network Operating System (NOS) sends request to
                  network server.
               3. Network connection carries request to server.
               4. Server NOS receives request.
               5. Server hard drive reads data.
               6. Server NOS sends requested data to workstation.
        The requested data then traverses this path (noted by arrows) in the
        opposite direction. During the Workstation's second access to above
        data the following will occur:
                  Ŀ            Ŀ
                        WORKSTATION                    NETWORK SERVER
                  Ŀ   Ŀ   Ĵ            Ŀ   Ĵ
                   WS <->CacheAll   NOS            NOS   Hard  
                  Apps    cache                          Drive 
                              
        Notice that the second time the workstation requests the server data,
        a much faster data path results:
             1.   CacheAll interprets data request from application.
             2.   CacheAll immediately returns the requested data.

        Thus CacheAll allows applications to run without going through the
   network, which can result in faster workstation operation, reduced network
   traffic and reduced server loading! NOTE: NETWORK DATA BASE USERS -- To
   prevent potential loss of your data, CacheAll will not cache shared data
   files which are simultaneously updated by multiple users across a network
   UNLESS you set these files to read only status.

        CUtil's LIST command allows viewing the cache activity of each
   workstation. Using this command you can see CacheAll cache local and
   network drives and also see which files are being cached!


   CacheAll Evaluation Manual                                          Page 41
   --------------------------------------------------------------------------
   -

                             Swap Files for CacheAll

                              What is a swap file?

        A swap file is an area of your hard drive which you set aside for use
   as additional "memory". Applications, such as CacheAll and Microsoft
   Windows, use a swap file to create the illusion that your PC has more
   memory than it really does.

        CacheAll is the first disk caching program that allows you to take
   advantage of a swap file to caching your storage devices. Using your hard
   drive as additional memory is inexpensive and can be quite beneficial,
   especially when using CacheAll to cache devices which are slower than your
   hard drive. For example,

     1) Dedicating your RAM to cache your fast devices, such as you hard
        drives, and dedicating a swap file to slow devices, such as CD-ROMs,
        allows you to provide a balanced performance increase across all of
        your devices. In this example, your hard drives would be made to
        appear almost as fast as RAM drives and your CD-ROMs appear to be
        almost as fast as hard drives.

        Note that you are always free to dedicate RAM to fast and slow
        devices, you must examine each CacheAll application on a case-by-case
        basis to determine the optimal caching method. Remember, when RAM is
        used for both fast and slow devices (i.e. Hard Drives & CD-ROMs) the
        slower devices can potentially monopolize the RAM cache at the
        expense of "fast" device performance gains.

     2) By installing CacheAll on each workstation of a network and creating
        very large caches through the use of RAM and SWAP FILE, a network
        manager can substantially reduce network traffic and server loading.
        This occurs because CacheAll will keep local copies of frequently
        used server data at each workstation. Therefore workstations do not
        need to go through the network to obtain data.

                      How does CacheAll use the swap file?

        To understand how CacheAll uses the swap file let's review basic
   cache operation. Caches maintain a copy of the most recently accessed
   data, and provide its copied data to applications much faster than the
   media on which the data was originally stored. When the cache program
   determines that new data should be added to the cache, data may have to be
   removed in order to make room for this new data. To achieve absolute
   maximum performance, we would prefer no data to be removed from the cache,
   but this is impossible since all computers have finite resources and so
   eventually run out of room. CacheAll addresses this issue by putting data
   removed from the cache RAM into a cache swap file (please refer to
   CacheAll's FAST option in section entitled CacheAll Options).

        Classical cache programs are only capable of using your computer's
   expensive RAM, and compete with other programs for this valuable resource.
   This is another example of CacheAll's advantages over other cache


   CacheAll Evaluation Manual                                          Page 42
   --------------------------------------------------------------------------
   -

   programs. CacheAll can use a swap file to effectively extend the amount of
   memory your computer contains. This also allows CacheAll to cache data
   other cache programs would have to throw away. This particular aspect of
   CacheAll is most useful for slow devices (slow relative to the speed of
   drive on which the swap file is placed), such as CD-ROMs, slow network
   adapters, and when CacheAll is used to reduce network I/O by implementing
   large local data caches.

                        Defining a swap file for CacheAll

        When CacheAll is started, it examines your "C" drive for its
   available disk space. Unless you specify otherwise, CacheAll will
   automatically use 50% of your available disk space (up to 4 Meg) for the
   swap file. You may use the DISKPATH option (See CacheAll's option section)
   to place the swap file anywhere on any of your writable drives. The
   default location is the root directory of your "C" drive.

             Note: to prevent potential loss of data, you should
             avoid placing the swap file on a compressed drive. You
             may use the DISKSIZE option to override the automatic
             setting and specify the desired size of the swap file.
             Note: to disable the swap file, simply specify a
             DISKSIZE of zero.

        Place the swap file on the fastest device you have connected to your
   system to achieve maximum cache speed. Note that it is wasteful to place
   the swap file on a RAM drive! It will work, but you will get better
   performance from CacheAll if you dedicate the memory used for the RAM
   drive to CacheAll directly as cache RAM. Use DRIVES and FAST to cache
   specific drives to the SWAP FILE.

   EXAMPLE:  You wish to place the SWAP FILE in the TEMP directory of the E:
             drive, and you wish to use the SWAP FILE to cache networked
             CD-ROMs H: & J:, network drives K: & V:, and no other drives are
             to be cached using the SWAP FILE.

   Option file or command line option settings:

                  DISKPATH=E:\TEMP
                  DRIVES=C-Z
                  FAST=C-GIL-UW-Z

   Notice that instead of specifying which drives are cached to the SWAP
   FILE, you must use the FAST command to EXCLUDE drives from the SWAP FILE!


   CacheAll Evaluation Manual                                          Page 43
   --------------------------------------------------------------------------
   -

                   Removing the swap file from your hard drive

                     ABSOLUTELY DO NOT REMOVE THE SWAP FILE
                           WHILE CacheAll IS RUNNING!

        When CacheAll creates the swap file, it sets the "hidden" attribute
   of the file to keep it from being inadvertently deleted. You can remove
   the file by using the DOS ATTRIB command BUT DON'T DO IT WHEN CacheAll IS
   RUNNING! If you use the default CacheAll settings for the swap file, you
   can execute the following commands to delete the swap file:

             ATTRIB  -H  C:\CACHEALL.SWP
             DEL  C:\CACHEALL.SWP

        If you chose a different swap file path with the DISKPATH option, you
   will have to substitute that path for C:\ (as used in the example).


   CacheAll Evaluation Manual                                          Page 44
   --------------------------------------------------------------------------
   -

                        Maximizing CacheAll's Performance

        To achieve maximum CacheAll performance there are several things to
   consider when "tweaking" CacheAll's options. Some guidelines are listed
   below:

      - Use DOS's FASTOPEN program to help minimize the time it takes to open
        a file. Refer to your DOS manual for instructions to setup up
        FASTOPEN.

      - Install a memory manager.

      - Use the swap file to cache slow devices like CD-ROMs, and when doing
        so use the DISKSIZE option to specify the largest swap file size
        possible. Doing this increases speed because more of the slow
        device's data will be read from the faster swap file drive.

      - BE SURE CACHEALL IS NOT RUNNING WHEN PERFORMING THIS TWEAKING
        PROCEDURE! To maximize access speed to the swap file, turn off the
        swap file's hidden and system attributes. Run a drive defragmentation
        program so that CacheAll's swap file will be contiguous. Restart
        CacheAll to return the file attributes to hidden and system.

      - When accessing a device that is faster than the device that contains
        the swap file (specified with the DISKPATH option), use the FAST
        option. This tells CacheAll to store the fast device data in only the
        memory cache, thus avoiding additional time in writing to the swap
        file. If you do not specify the FAST option for faster devices,
        CacheAll may slow file accesses instead of speeding it up. CacheAll's
        automatic settings assume local and network drives are FAST, which
        may be incorrect in some cases.

      - Use the SMALLFILES=N option. If you are working with many small files
        (files which are smaller than the BLOCKSIZE used by CacheAll), this
        option can increase your performance by telling CacheAll not to cache
        small files. An example of when this would is useful is when running
        Norton Desktop for Windows.

      - If you are caching very large files, greater than 128Mb, be sure your
        BLOCKSIZE is large enough. (Full details in commerical manual).

      - Use CUtil's LIST function to determine when and which files are being
        used by your applications (use CUtil's FLUSH=* to flush the cache and
        erase the file list). In this way the LIST command can help you to
        determine which files are most frequently used and so are most
        beneficial to cache. By grouping these frequently accessed files
        together in a directory and only caching that directory you may be
        able to substantially increase your system performance by focusing
        cache resources on that directory. See manual regarding caching
        specific areas of a drive to see how to cache specific directories.


   CacheAll Evaluation Manual                                          Page 45
   --------------------------------------------------------------------------
   -

                     What CacheAll version 1.0e will not do

   Issue:    CacheAll v1.0e will not negotiate RAM use under Windows.
   --------> Conserve RAM use by setting MEMSIZE to the maximum desired value
             under Windows and use a large SWAP FILE to cache CD-ROMs and
             network drives.


   Issue:    ************ FOR NETWORK DATA BASE USERS ONLY ***********
             To prevent potential loss of your data, CacheAll v1.0e will not
             cache shared data files which are simultaneously updated by
             multiple users across a network UNLESS you set these files to
             read only status.
   --------> To cache such files, make them read only where possible.


   Issue:    CacheAll v1.0e does not perform delayed writes.
   --------> If you wish to perform delayed writes for your local hard drive
             you can use CacheAll with another cache, such as SmartDrive. 
             Since delayed writes have no meaning for CD-ROMs or networks,
             simply use CacheAll to cache those drives and the other cache to
             cache your local drives.


   Issue:    CUtil's LIST command reports certain files are not always cached
   --------> This can be caused when a file is shared by multiple users or
             applications. Note, EXE's are not always cached but their
             overlays are usually cached.


   CacheAll Evaluation Manual                                          Page 46
   --------------------------------------------------------------------------
   -

                          CacheAll's Automatic Settings

   CacheAll will,

   Setting:  use 25% of available RAM
   Override: use MEMSIZE to specify a different setting

   Setting:  place SWAP FILE in the root of your "C:" drive
   Override: use DISKPATH to specify a different drive and/or directory,
             remember to avoid placing SWAP FILE on a compressed or network
             drive

   Setting:  use 50% of available drive space on "C:" up to 4 Megabytes
   Override: use DISKPATH to specify a different drive and/or, DISKSIZE to
             specify a different setting, set DISKSIZE=0 to disable SWAP FILE

   Setting:  not cache drives "A:" and "B:"
   Override: use DRIVES to select drives to cache

   Setting:  cache only local CD-ROMs to the SWAP FILE
   Override: use the FAST command to select the drives which should NOT be
             cached using the swap file
   Note:     CacheAll does not typically "see" CD-ROMs accessed over a
             network and so may require the user to manually specify these
             CD-ROMs.

   Setting:  choose BLOCKSIZE (based on value of MEMSIZE) to minimize RAM
             usage
   Override: use BLOCKSIZE to specify a different value, BUT REMEMBER --
             setting BLOCKSIZE to its maximum value of 16 WILL NOT
             necessarily maximize performance, to maximize performance you
             must slowly increase and decrease the BLOCKSIZE setting for your
             particular application, "when in doubt, leave it out!"


   CacheAll Evaluation Manual                                          Page 47
   --------------------------------------------------------------------------
   -

                                 Common Problems

   CacheAll Not installed:
        Check your AUTOEXEC.BAT
             Example -- LANtastic installs a line similar to below,

                  C:\LANTASTI\STARTNET.BAT

             in your AUTOEXEC.BAT. This line runs STARTNET.BAT but after
             execution any lines which follow, such as CacheAll's install
             line, are not executed. To correct this simply do what
             CacheAll's installation program does and use a CALL statement to
             change the above line to:

                  CALL C:\LANTASTI\STARTNET.BAT

             Now after STARTNET.BAT is completed, control will return to
             AUTOEXEC.BAT.

   Starting Networks from BATch file other than AUTOEXEC.BAT:
        CacheAll must be installed AFTER your network. To correct this unload
        CacheAll before starting your network and add CacheAll's installation
        line to the end of the BATch file that installs your network. This
        line may be copied from your AUTOEXEC.BAT after CacheAll is
        installed.

   Local Hard drives are slower using CacheAll
     1) CacheAll's automatic setting use 25% of available RAM, your previous
        cache was probably set to use more RAM. Set CacheAll RAM cache size
        to the same value as your previous cache using the MEMSIZE option.
     2) This may occur when using CacheAll to replace a cache which had been
        providing delayed writes (CacheAll v1.0e does not support delayed
        writes). If you wish to continue performing delayed writes, use
        CacheAll in conjunction with a cache program such as SmartDrive.  But
        remember, delayed writes have no meaning for CD-ROMs. Also remember
        that no other cache program can cache network drives.
     3) CacheAll performs read aheads to improve file access performance. In
        some cases the value of BLOCKSIZE may be too large for the type of
        data you typically work with. To improve performance, reduce the
        value of block size until maximum performance is achieved. If you
        wish to tweak BLOCKSIZE do so by SLOWLY increasing and decreasing its
        value until the optimal setting is found.

   My computer has recently become unstable.
        This problem can occur when using a batch file other than
        AUTOEXEC.BAT to startup your network. When starting your network in
        this manner, unload CacheAll at the beginning of the BATCH file and
        load CacheAll at the end of the file. Also, when starting CacheAll
        manually be sure to do so AFTER all device drivers, redirectors and
        network software is installed!


   CacheAll Evaluation Manual                                          Page 48
   --------------------------------------------------------------------------
   -

                                Common Questions

   How is CacheAll different than other caches?
        Other cache programs only cache local hard drives, floppy drives and
        sometimes CD-ROMs but CacheAll can cache ANY device which can be
        accessed as a drive letter (such as C: or D: or R:). CacheAll will
        cache CD-ROM drives, network drives, hard drives, floppy drives,
        optical drives and any other drive you can normally access from your
        PC. CacheAll is also the only cache that allows you to use a SWAP
        FILE to cache any device. CacheAll is also the only cache that allows
        you to cache only a section of a storage device rather than the
        entire drive.

   What about CacheAll benchmarking?
        Be careful using benchmarking programs to determine CacheAll's true
        performance. Many benchmarking programs say that CacheAll provides no
        performance increase because they are designed to test cache programs
        such as SmartDrive. CacheAll uses a completely new technology that
        many benchmark programs were not designed to test. When this happens
        no difference is noted. The best way to test CacheAll is to run a
        scenario of tests (such as doing CD-ROM searches) without CacheAll
        and then do the same series of tests with CacheAll loaded and note
        how much faster the test is when CacheAll is running. Remember -- as
        with other cache programs CacheAll will show greater performance
        benefits when you perform an operation more than once.

   Is CacheAll installed in my CONFIG or AUTOEXEC?
        In most cases CacheAll should be installed at the end of your
        AUTOEXEC.BAT.

   I only use a network sometimes, should I install for standalone or
   network?
        When installing CacheAll for standalones, CacheAll will refer to the
        STDALONE.OPT file for it's option settings. This ".OPT" file contains
        the statement ALLFILES=A-Z which should not be used for networks (see
        ALLFILES in CacheAll Options section)! When running your network,
        change RUNCA.BAT to run NETWORK.OPT instead of STDALONE.OPT, and for
        maximum standalone performance remember to switch it back when not
        using the network. You may wish to perform this operation by writing
        a batch file.

   Is CacheAll Windows compatible?
        Yes! If you are running Microsoft Windows 3.0, you must add the line:

                  InDOSPolling=1

        to the [386Enh] section of SYSTEM.INI. If you do not know how to
        modify the SYSTEM.INI file, please refer to your Microsoft Windows
        documentation. If you are using Microsoft Windows 3.1, you do not
        need to make any changes.


   CacheAll Evaluation Manual                                          Page 49
   --------------------------------------------------------------------------
   -

   What do I need to do to configure CacheAll?
        Nothing! In fact we suggest that you don't set any options but, if
        you must, only adjust the MEMSIZE, FAST, and DISKSIZE options.
        Remember --adjusting options incorrectly will degrade performance.


   CacheAll Evaluation Manual                                          Page 50
   --------------------------------------------------------------------------
   -

                              Notes to CD-ROM Users

   CD-ROM applications which have large files (greater than 128Mb)
        If you are using a CD-ROM application which has large files, you
        might need to increase the BLOCKSIZE setting to increase performance.

   Maximizing Performance
        Set DISKSIZE's value as large as possible (refer to MANUAL.TXT for
        maximum value of approx. 64 Megabytes). This will cause most CD-ROM
        accesses to occur from your hard drive.


   CacheAll Evaluation Manual                                          Page 51
   --------------------------------------------------------------------------
   -

                             Notes to Network Users

   Artisoft LANtastic(TM)
        LANcache DOES NOT cache network drives, only local hard drives.
        CacheAll caches all drives... network, hard drive, CD-ROM, etc.

   Diskless Workstations
        CacheAll can be used on diskless workstations (sometimes called
        remote boot workstations).  It will work best if you disable the swap
        file using the DISKSIZE=0 option.  You can put the swap file on a
        network drive, but you might sacrifice some performance benefits,
        depending on how you use CacheAll.  The following steps outline one
        way of installing CacheAll onto a diskless workstation (this
        procedure is geared towards LANtastic, but should apply to most other
        networks):
             1.   Install CacheAll onto the file server.
             2.   Create a resource/alias for CacheAll called CACHEALL.
             3.   Boot the diskless workstation.
             4.   Now, do one of the following:
                  a.   Modify the AUTOEXEC.BAT for the diskless workstation
                       to connect to the resource CACHEALL and run the
                       CACHEALL program.
                  or

                  b.   Run CACHEALL directly from the CACHEALL resource

        This procedure should get CacheAll up and running on a diskless
        workstation.  One other step you can do is to copy the CACHEALL.EXE
        program over to the boot image to run it directly from the boot
        image.

   Where should CacheAll be loaded?  My Server or Workstation?
        CacheAll is designed to be run on each workstation on your network.

   CacheAll Increases Network Performance
        Running CacheAll on ALL workstations or non-dedicated servers of a
        network provides several important benefits by reducing network I/O
        requests:

             1. Reduced network traffic
             2. Increased workstation speed
             3. Reduced server load
             4. Use CUtil's LIST command to view cache file listing


   CacheAll Evaluation Manual                                          Page 52
   --------------------------------------------------------------------------
   -

   Maximizing Network Performance
        When using CacheAll on a network, we recommend setting all program
        files to be read only.  This can usually be done using the DOS ATTRIB
        command.  You can say the following:

                  ATTRIB +R *.EXE
                  ATTRIB +R *.COM

        Those two lines will force all files with the extensions EXE and COM
        in the current path to be set as READ ONLY files and thus will be
        cached by CacheAll without needing to set ALLFILES.  You might find
        other files, such as overlays, which can also have the READ ONLY
        attribute set.

   DEDICATED Servers
        If you have a dedicated server you should continue running programs
        such as SmartDrive as these programs will increase the servers "serve
        speed" to the network.  BUT, these programs should be removed from
        your workstations and replaced by CacheAll.

   Networks versus Standalone operation: ALLFILES!
        Unless directed otherwise, using the ALLFILES option, CacheAll will
        only cache files which are opened in EXCLUSIVE or DENY WRITE modes.

        1) Network user
             If you are using CacheAll on a drive which is used exclusively
             by one user (or not on a network), you can use the ALLFILES
             option for this drive. The ALLFILES option will force CacheAll
             to cache all the files on the specified drives, regardless of
             how they are opened. YOU MUST BE SURE NO ONE ELSE CAN MODIFY THE
             FILES WHILE THEY ARE BEING CACHED WITH THE ALLFILES OPTION.

        2) When not connected to a Network (i.e. "Standalone")
             Set
                  ALLFILES=A-Z
             For maximum performance. This will be done automatically if you
             told the installation program that your PC was a standalone
             PC.

   Shared files
        CacheAll will only cache files which are opened in EXCLUSIVE or DENY
        WRITE modes.  If you are using CacheAll on a drive which is used
        exclusively by one user (or not on a network), you can use the
        ALLFILES option for this drive. The ALLFILES option will force
        CacheAll to cache all the files on the specified drives, regardless
        of how they are opened.  YOU MUST BE SURE NO ONE ELSE CAN MODIFY THE
        FILES WHILE THEY ARE BEING CACHED WITH THE ALLFILES OPTION. Use
        CUtil's LIST command at each workstation to determine who is using
        what and when.


   CacheAll Evaluation Manual                                          Page 53
   --------------------------------------------------------------------------
   -

      AppTrack(TM) Makes Software audits a nuisance rather than a concern -

                             AppTrack 1.0 Features:

   AppTrack is a full-featured license management and program restrictor for
   LANtastic networks that reduces network management headaches by
   guaranteeing you pass every software audit!

                        Application Management Features:

   1)   Without workstation TSR's, AppTrack manages and restricts program
        usage,
            Allows network managers to guarantee software license adherence
             across a network
            An unlimited number of Microsoft Windows and DOS applications
             can be managed simultaneously
            Applications can be managed across multiple servers

   2)   Provides maximum security for your licenses,
            End user cannot copy applications
            Fully encrypted network packets and database
            System manager privileges are required for management access and
             control

   3)   Includes easy to use, Microsoft Windows based, Console as a control
        center

                           AppTrack Console Features:

   1)   "At-a-glance" application display,
            Displays currently executing applications and who is running
   them
            Shows peak usage of an application
            Easily spot excessive licensing
                  - Reduce software costs!

   2)   Extensive data collection. Data and it's views,
            Can be exported to several formats
                - fully documented custom exporting facility
            Can be included in reports to Management
            Can be customized & saved for later retrieval
            Includes application transaction history
                - Application & User name, Start & Stop time, ...

       To order AppTrack, contact C&D Programming Corp. at (800)847-5676 
                          (outside U.S. (801)582-0503)


   CacheAll Evaluation Manual                                          Page 54
   --------------------------------------------------------------------------
   -

              Reseller Qualification Form: C&D Welcomes Resellers!

        C&D thanks you for your interest in reselling our products!  Our
   screening process protects your business by making it simple for
   legitimate applicants to establish reseller status, and preventing end-
   users from obtaining reseller discounts. We require a copy of your
   currently valid reseller's permit, your currently valid sales tax
   identification certificate for your state, or your currently valid goods
   and services tax certificate for your country, simply supplying the
   reseller number is NOT sufficient. To confirm that you are a reseller of
   computer products and/or services, we require a copy of promotional
   material from you. This is sufficient to establish reseller status with
   us, and much simpler than filling out an elaborate dealer agreement. When
   mailed to us we will accept any of the following as promotional material:
      - Your company brochure for a product you design, manufacture, or sell.
        It is not adequate to just draw something up on your computer and
        print it out on your printer.
      - Or, a page from a recent newspaper, magazine, Yellow Pages, or other
        publication showing an advertisement for your company and it's
        products.
      - Or, a photocopy of your company name and phone number from a
        computer-oriented section of The Yellow Pages. This does not need to
        be an actual advertisement the basic listing which the phone company
        provides, provided it is in a computer oriented section, is adequate.

                              Company Information:

   Company Name____________________________________________________________

   Address_________________________________________________________________

   City ____________________________  State _____________ Zip _____________

   Phone _________________________________ FAX_____________________________

   Contact_________________________________________________________________

   D&B Account # _________________________ Date ______________ Rating _____

   How did you hear about C&D?_____________________________________________

   I certify that the above company is a legitimate reseller of computer
   products and/or services.

   Signature _______________________________________ Date__________________

   Printed Name ____________________________________ Title_________________
   To receive a reseller package, mail (or Fax to 801-581-0883) this
   completed form with the requested information:
                       C&D Programming Corp.
                       New Accounts (CAEVAL1.0e)
                       P.O. Box 581012
                       Salt Lake City, Utah 84158 USA
